Aluminium Alloy - BS-L - L113 T6 Sheet

L113 T6 Sheet

Aluminium alloy L113 – 6082T6 is a medium strength alloy with excellent corrosion resistance. It has the highest strength of the 6000 series alloys. Alloy 6082 is known as a structural alloy. In plate form, 6082 is the alloy most commonly used for machining. As a relatively new alloy, the higher strength of 6082 has seen it replace 6061 in many applications. The addition of a large amount of manganese controls the grain structure which in turn results in a stronger alloy.
In T6 temper, the alloy machines well.


Chemical Composition

Spec: BS L113(1971)

Alloy L113

Chemical Element % Present
Chromium (Cr) 0.0 - 0.25
Copper (Cu) 0.0 - 0.10
Iron (Fe) 0.0 - 0.50
Magnesium (Mg) 0.50 - 1.20
Manganese (Mn) 0.40 - 1.00
Nickel (Ni) 0.0 - 0.10
Lead (Pb) 0.0 - 0.05
Silicon (Si) 0.70 - 1.30
Tin (Sn) 0.0 - 0.05
Titanium (Ti) 0.0 - 0.20
Zinc (Zn) 0.0 - 0.20
Aluminium (Al) Balance

Properties

Physical PropertyValue
Density 2.70 g/cm³
Melting Point 555 °C
Thermal Expansion 24 x10^-6 /K
Modulus of Elasticity 70 GPa
Thermal Conductivity 180 W/m.K
Electrical Resistivity 0.038 x10^-6 Ω .m

Spec: BS L113(1971)

Sheet - 0.2mm to 3.0mm inc.

Mechanical PropertyValue
Elongation A50 mm 8 Min %
Tensile Strength 295 Min N/mm2
0.2% Proof Stress 255 Min N/mm2

Alloy Designations

Aluminium alloy L113 has similarities to the following standard designations and specifications but may not be a direct equivalent:

6082


Temper Types

The most common temper for L113 – 6082 aluminium is:

  • T6 - Solution heat treated and artificially aged

Supplied Forms

L113-6082T6 aluminium is supplied in sheet, strip and plate.

  • Plate
  • Sheet
  • Strip
Download PDF Version

Datasheet Search

Last Datasheet Revision

8 July 2016

Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.